DVD in motion patch for NR261EM - Page 3

And how can i do it with 00.31.10?? sorry for my english but i need help.. please

Hi to all!

I finally tried to "upgrade" my car (2.0 DI-D Instyle +navi)  with this CD:
Outlander Update CD, NR261-EM, Software version Version E, DVD in motion allowed

Before update data was:
SW Version: F
Loader NR-261EM 1.09
Aplication 00.31.08

After "update" i got this data:
SW Version: E
Loader NR-261EM 1.09
Aplication 00.31.06

With that, I was actually downgraded the software, but the DVD plays with picture.
I didn`t notice anything missing from previous version.
If somebody have a newer version, please share...

Zox.

Hi,
I''m from Australia and we''re a little backwards down here.... what with riding Kangaroo''s and everything. I''ve checked out a few Aust forums for this patch and they all direct me back here. What am I doing wrong? I''ve downloaded the file MMCS-E-DVD.rar and I used winzop and it converted it to MMCS-E-DVD.iso. I burnt it a CD and stuck it in and it said check disc. I tried it on a DVD with the same result. I even tried it in the SatNav slot below the cd slot to no avail. Start again and speak very slowly.
PM me if you don''t want to jam the post with garbage.
 
Thanks

Updating procedure
^^^^^^^^^^^^^^^^^^
1. Extract files from archive.
2. Burn the ISO file on a blank, fresh CD (in NERO, Menu -> Recorder -> Burn Image)
3. Start the engine and insert the burned CD into MMCS'' unit
4. Wait for it to check the disk and to start the upgrade procedure. It may take up to a minute do make the checks.
5. Wait for the update procedure to finish. This will take 3 to 5 minutes. At the end the unit will reboot.
6. After start, you will be prompted AGAIN to update. Choose NO, the unit is already updated.
7. Remove the CD.
8. Drive carefully while enjoying your DVD movie

Tried again, same result. Check disk.
A. When I unzip I get a MMCS-E-DVD.iso file. Is this correct and all I burn, and
B. I''''m not sure what software version I''''m running. It''''s in a Lancer but I''''m sure they''''re all the same unit. Maybe I have a different software version and this is the problem?
P.S. I didn''t have the engine running just of ACC. Do I have to have it running? I didn''t think it would make a difference

I am a newone so, dear fellows, otaku, brian, zox rocsin & all the rest of you...... fantastic job & information u gave us.
Have an Out.08 2.4 CVT Instyle, that is fully loaded at least here in Athens Greece. I applied the "in motion" patch
on my mmcs BLD#261EM 1.09, applic. 00.31.06 and all went so smoth!!! Now every body can enjoy a DVD in motion
less my self.... cause I am driving. Hope you will soon find a patch for the aux A/V inputs (which thanks to u again I found
hidden under the middle arm rest & acivated them by adding RCA inputs)
Thanks a lot to every body.

Does anyone have a In Motion update for this version?

2008 Mitsubishi Lancer Sports Sedan Instyle+

Loader: BLD-NR-261EM 1.09
Application: 00.31.10
Navi Sub Microcomputer: 00.31.00 090004
Audio Microcomputer: 09.30.03 093003
Map Data: M110 AEU_07_200701B
Monitor: 00.27.00
CAN BOX: 000120

@Cyric313
I think you could do it with CD mentioned few post earlier, and you get only lower aplication version (Aplication 00.31.06) but you will have a picture while driving.

Zox.

PS. We are waiting for some new updates from Otaku who is the king for that....

  Well, it appears from here that those with the EM versions can do the hack with versions newer then the hack version and it will work.  Those that have the UM version can''t use the hack if you have a version newer then the 30.94.    Least it looks like that from reading these post.
I''''m sad, cuz I have the 30.99 UM version and no hacky. 
Otaku, you need fresh donations?

i tried with the CD you mentioned Zox. but i got the same error some oothers have gotten.

i load the CD in the drive, it checks the disk and then nothing happens...

DOUBLE CHECK THAT DOWNLOADED FILE IS OK & BURNING OF THE ISO IS VERIFIED BY THE PROGRAM U USE ( I USED ROXIO CREATOR & TDK CD-R80).

@Cyric Actually, I got an error message from winzip,when extracting a "MMCS-E-DVD.rar" file, "Invalid or corrupt authenticity information" but I burned that .iso to a CD without any problem. Do you wait a minute-two when "checking disc" is displayed?

Zox.

I got the same "invalid/corrupt" message but I also burned the ISO whithout  problem and use it on my 216EM 1.09 appl.00.31.06 with perfect results.

I have an 08 Lancer w/ version 00.20.68 navi unit. I followed the patch as described, but when I pop the CD in it says.."Insert product up key into KEY slot"...Does anybody have any idea how to get past this screen...please help! Do I have to go to the dealer to get this "key"...does something have to be plugged into the jack in the bottom of the nav screen when it flips out?...Any help would be greatly appreciated.

Sorry I have no idea, one thing for sure the dealer wan''t give u a key in order to apply the "patch"... the jack is for a "key" but from what I know is for GPS map updates.

I think you just downloaded the wrong patch file. The correct patches are on rcostin''s website. The "upgrade key" is for a total map upgrade, not the dvd in motion upgrade.

Tried to do the upgrade, I have: Loader: BLD-NR-261EM 1.09 and Application: 00.31.06 in a -08 Outlander bought new in Norway.
 
Did as the readme file said, but I made the disc in roxario as others have done and had success with.
 
But not me, MMC told me "cheching disc" and then "check the disc"
 
Will try burning in NERO ASAP :)

I am much surprised, Elzouavo & myself have the same unit particulars as yours & patch worked fine. Did you follow exactly the procedure described by Zox in previous page 6?? Try to use a different copy program & a different brand of cd, I used TDK CD-R80.

Have DL Nero now, wil try again :)

New disc made with Nero, works great.
 
Thanks Otaku and all others who made this posible :)

Normal 0 21 You’re doing a great job, everybody! I bought my outlander (a super-black ''Instyle'') in France, few days ago.  My MMC (261EM, applic 00.31.06) has accepted very easy the patch:
(http://www.deltainfo.ro/manuals/mitsu/outlander)

can''t wait for the next one: for the AUX in motion...

a few little questions:
1. Does the MMCS contain a TV receiver (not activated?) if ''yes'': an analogical or digital one?
2. Pity that this MMC with a HDD can''t copy the mp3 or avi files... Once the copies are writed on the unlocked HDD, can the MMCS reading them (mp3, mpeg2, mpeg4...)?
3. the copied CD''s are encoded (shrinked)? How many hours of music we can storage?
4. no USB / memory card extension ?!? We’re in 2008, no other quality-media stuff produced without a sort of memory extension these days!

Thank’s a lot for your affected time in this work and for your public results!

Yes Otaku is the master of the game.... told you it will work with a different copy program. To Eduardena, no TV tuner, no usb, no memory card slot(s)..... you need a new commercial unit for these....

Many thanks for this motion patch, can''t wait to go for a drive tomorrow. Downloaded etc using an imac and an unbranded cd..can''t believe how easy it''s been - awesome, thanks again to you all...ps mine''s an Outlander Diamond 2.2 diesel - best SUV on the road and tonight has gone one stage further!

Here are the original files from version 3110 (EVO X) (NR261EM)

http://rapidshare.com/files/150779432/3110.zip

Tried again, same result. Check disk.
I tried with different burn software (this one actually showed the 2 .kwi files) burnt as an image to a cd, stuck it in the slot.
Does the car need to be running? Does the CD need to be closed? Because I can''t find an option ANYWHERE on my notebook to close a disk.
How do I find out which software version my MMCS is running?