Reverse Indiglo Gauge Install
Login  | |
|
Reverse Indiglo Gauge Install - 7/15/2007 12:17:04 PM
|
|
|
Joshewuhh
Posts: 1734
Joined: 1/11/2007
From: Hammond, LA
Status: offline
|
Glow Guage install. Done on a 99 Eclipse RS (Procedure same for GS)
Tools needed:
Phillips screwdriver
Flathead screwdriver
Wire crimpers
Heatshrink tubing
10mm Socket and wrench
Test Light
Patience & more patience
So you bought some fancy pants glow gauges and need to install them, well here ya go.
Your kit should be similar to this
Alright, lets get into this.
Installing the gauges:
Before starting, disconnect the battery.
Alright, now remove the trim ring around the instrument cluster. There are 2 screws in it and it pulls right out.
The undo the 4 Gold screws holding the cluster and pull out the cluster.
Remove the clear plastic cover, and the next plastic cover.
Slide the Temp gauge insert over the exsting gauge. Do the same for fuel.
Now, some of that patience is gonna go into effect.
Remove the needle from the speedometer by prying it upward with a small amount of force.
Insert speedo gauge and replace need exactly how it was. If done right, if you move needle by hand then let go, it should return to 0mph.
Repeat for tachometer.
Run gauge wires though openings in cluster.
Replace the black cover, but make sure everything is lined up perfect when replacing.
Make sure all the snaps engage tightly, then replace the clear plastic shield.
Installing the power inverter and wiring it up:
Heres where you need some of that more patience stuff.
Pop out to 2 covers on the knee cover. Big one on the left, small on the right.
Using your 10mm ratchet, undo the 2 nuts you exposed, and there are 2 more at the bottom of the panel.
Remove panel.
Pop out the cover where the cruise control/foglight/etc. goes.
Now, crawl underneath your dash and remove the bolt on the gold bracket (You can't miss it), then unscrew the stock dimmer switch and unplug it.
Pull the wiring up through the hole you made by removing the trim cover, the dimmer runs on the same harness.
Peel back about 4 inches of the wire cover.
The green/white wire is the dimmers power wire. Cut it and strip it 1/4in off. Slip a 1 inch piece of heatshrink onto the wire.
Splice the power wire from your inverter to the dimmer power, then reconnect both wire ends and melt the heatshrink onto it.
Now, run the plugs for the gauges through the giant opening to the right.
Connect your ground to the bolt on the gold bracket.
Connect the gauge wiring to the connector and insert the gauges.
Reconnect the factory dimmer and plug it back in.
In the panel where all the wiring is behind, drill a 3/8inch hole and stick in your dimmer switch.
Now, reconnect the battery and turn on the lights to make sure you did it right.
If so, go backwards and start putting everything back together. Clean up your wiring, etc.
Finished product:
All in all, it takes about an hour and a half to do this.
Not as hard as it seems.
If your speedo is off calibrated, remove the needles while the car is running and set the speedo needle at zero, and match the rpm's to your normal idle.
Kind of a redneck way to calibrate, but it works.
_____________________________
Neah...
|
|
|
|
|
|
|
RE: Reverse Indiglo Gauge Install - 7/15/2007 12:28:38 PM
|
|
|
Dusty Eclipse
Posts: 4368
Joined: 2/23/2007
From: 11746,21114,34668
Status: offline
|
Good install, look how wierd the foglight/mirrors panel looks with nothing there.... wow...
_____________________________
Current cars: (What I havent wrecked)
1995 Eagle Talon TSi "Jackie"
2001 Mitsu. Eclipse GT "Dusty"
2000 Volvo V70R AWD "Mindy"
|
|
|
|
|
RE: Reverse Indiglo Gauge Install - 7/15/2007 1:03:50 PM
|
|
|
Kaede.Noir
Posts: 1719
Joined: 10/10/2006
Status: online
|
A nice basic tutorial for starting to mod the cluster :) ftw monkey beater :)
_____________________________
''98 2g 420a
-Custom Aluminum radiator
-Short ram shroom intake
-No rice
''83 GTI 1.8 *SOLD*
"the boat is gone, but now we got this huge gaping hole in the fence"
|
|
|
|
|
RE: Reverse Indiglo Gauge Install - 7/15/2007 3:32:16 PM
|
|
|
silvercoupe97
Posts: 3146
Joined: 11/10/2006
Status: offline
|
Nice Josh - monkey beater? lmao.
_____________________________
Thanks,
John
6 bolt/2g head,1G rods/2G pistons,FPBig28,MBC,Forge 1G DV,alky inj,AFPR,255lph,780cc, 3" turboback,Centerforce,4 spider,FMIC, Prosport Boost&EGT gauges,AEM wideband,DSMlink, AGX/Skunk2
|
|
|
|
|
|
|
RE: Reverse Indiglo Gauge Install - 7/16/2007 6:53:20 AM
|
|
|
RCJr9186
Posts: 5632
Joined: 7/27/2005
From: Summerville, SC
Status: offline
|
nice write up man!!!! very detailed. good call b/c it was PITA installing mine also.
_____________________________
quote:
Sebba
Use.... the.... FU CKING SEARCH BUTTON.
|
|
|
|
|
RE: Reverse Indiglo Gauge Install - 7/16/2007 4:14:42 PM
|
|
|
Kaede.Noir
Posts: 1719
Joined: 10/10/2006
Status: online
|
Im really tired of the stock ones... seriously, but for some reason im not a very big fan of indiglo gauges, they look cool, but i want something more classy.... i want something white and black!!! kinda like the dashboard of the 2005 accord
_____________________________
''98 2g 420a
-Custom Aluminum radiator
-Short ram shroom intake
-No rice
''83 GTI 1.8 *SOLD*
"the boat is gone, but now we got this huge gaping hole in the fence"
|
|
|
|
|
RE: Reverse Indiglo Gauge Install - 7/16/2007 4:27:45 PM
|
|
|
silvercoupe97
Posts: 3146
Joined: 11/10/2006
Status: offline
|
quote:
ORIGINAL: Kaede.Noir
Im really tired of the stock ones... seriously, but for some reason im not a very big fan of indiglo gauges, they look cool, but i want something more classy.... i want something white and black!!! kinda like the dashboard of the 2005 accord
I used to have them too and I prefer the black gauge....for nothing more than keeping her a sleeper of course. 
I've looked around before and remembered that there's a site that lets you customize your gauges. Here's one that I would get..just for the turbo model.
Thumbnail Image
You can set them up in just about any style you want..just about.
Here's the site.
http://www.speedhut.com/el_detail.asp?catagory=MITSUBISHI&auto_number=41&bhcp=1
 Attachment (1)
< Message edited by silvercoupe97 -- 7/16/2007 4:32:34 PM >
_____________________________
Thanks,
John
6 bolt/2g head,1G rods/2G pistons,FPBig28,MBC,Forge 1G DV,alky inj,AFPR,255lph,780cc, 3" turboback,Centerforce,4 spider,FMIC, Prosport Boost&EGT gauges,AEM wideband,DSMlink, AGX/Skunk2
|
|
|
|
Contact Us |
Sitemap |
Link To Us |
Advertising |
Automotive Links |
Mitsubishi Links |
Archive |
About Us |
Legal |
Privacy Policy |
© Mitsubishi Forum
Mitsubishi Forum .com is not affiliated with or endorsed by Mitsubishi Motors.
|
Printable Version
