Hood dents at Hinge Location (2007 XLS) (Full Version)

Mitsubishi Forum >> Mitsubishi Models >> Mitsubishi Outlander

Hood dents at Hinge Location (2007 XLS)

  

tx.mitsu -> Hood dents at Hinge Location (2007 XLS) (4/22/2008 10:23:08 AM)


I have started to noticed small dents on the top my hood right where the hinges attached from underneath. Having a black outie makes every dent and ding show up.
 
These can be seen from an angle, looking across the hood.
 
I will try and take photos, soon.
 

 
Anyone else see or have this happen yet?

  
antlip -> RE: Hood dents at Hinge Location (2007 XLS) (4/22/2008 1:42:10 PM)

I have a grey outie and noticed a ding in the center of my hood. I never knew a rock could fly up and ding the center top section of my hood like it did. But its there and it could only be from a rock.

2g0s0r1 -> RE: Hood dents at Hinge Location (2007 XLS) (4/26/2008 10:24:52 PM)

quote:

ORIGINAL: tx.mitsu


...small dents on the top my hood right where the hinges attached from underneath


EVERYONE PLEASE RESPOND TO HIS POST!  (Yes or No)
 
I also have these same dents(creases/ripples) at the same location on my 2007 LS AWD!  My mom also has a 2007 XLS with them!

I will take pictures of both cars and post them monday.  Im thinking it could be a widespread problem and the dealer should be responsible to fix it if alot of cars have the same issue.

I noticed it about a week after buying my silver outie... knowing that i didnt cause the dents.  Then i saw them on my moms and was like WTF?

Lets get this noticed please!

-Jimmy

Printerman -> RE: Hood dents at Hinge Location (2007 XLS) (4/27/2008 5:57:39 AM)

Hi All:

I have a bright Red 2007 XLS and It would be very visible if I had this problem and I don't......

[:)]

Cuffy -> RE: Hood dents at Hinge Location (2007 XLS) (4/28/2008 7:56:40 AM)

Anyone got pics?  I haven't noticed any on mine yet, but the hood has only been opened a few times.  More frequent use of the hood may put additional stress on the hinge attachment points.

With the sheet metal used by auto manufacturers getting thinner every year, this is probably going to be a common problem.  Do you guys recall the earlier post about the tire jack bumping the inside of the storage compartment and causing a dent on the outside of the rear quarter panel.  If that's any indication of how easy it is to dent our 'Landers then we haven't heard the last of these types of issues.

roach -> RE: Hood dents at Hinge Location (2007 XLS) (4/28/2008 8:54:35 AM)

So far nothing on mine Got the XLS since august 07

Outie08 -> RE: Hood dents at Hinge Location (2007 XLS) (4/28/2008 2:58:49 PM)

Nothing on mine either, got mine silver 08 XLS since Nov 07

I access under my hood at least twice a month to clean / check belts / levels / etc after I've done cleaning it. I am not aware this action may put stress on the hings which cause damage to the hood...

The hings are attached via a hollow U-channel under the hood, I cannot conclude that the reported dents may be due to the stress being put on the hings, likely a manufacturing defect.


[image]local://upfiles/16364/93CA469966E3498FB2B628955761C9D3.jpg[/image]

[image]local://upfiles/16364/B2278E71FB0F4E978AE72DD633C4FCFC.jpg[/image]

Cuffy -> RE: Hood dents at Hinge Location (2007 XLS) (4/29/2008 3:25:38 AM)

Good pics.  Your deduction makes sense that the opening/lowering of the hood shouldn't be related to the dents.  It's odd that several members have similar issues though.

Maybe those of you with the dents could post pics of them so we could compare and see if we can determine a commonality (like a service tech leaning on the hood, or hood flexing during opening/closing).

rtrackr99 -> RE: Hood dents at Hinge Location (2007 XLS) (4/29/2008 12:02:05 PM)

My Outtie is an early 2007/January and so far, I don't have any dents.  You can see this in the recent photos of my LED lights.

Could how hard the hood is closed be a factor in the hinge dents?
I'll only release the hood from the lowest height that the hood will latch, about 4 inches. (From the bottom point of the latch)
The hood does seem to be kinda heavy.

Aloha!
Take care!

Kwanger -> RE: Hood dents at Hinge Location (2007 XLS) (4/29/2008 12:17:06 PM)

Not seen them on my 2007 either

  

Page: [1] 2 3 4 5   next >   >>

Return to Mitsubishi Forum home page or view the Full Version of this page.